esd suppressor design and speci cations are each subject to change without notice. ask factory for the current technical speci cations before purchase and/or use. should a safety concern arise regarding this product, please be sure to contact us immediately. & 1 ; 2 " 3 & 4 ( 5 6 " 7 8 9 " 10 9 11 product code esd suppressor size code 1 2 3 size (inch) 0603 (0201) 1005 (0402) 1608 (0603) packaging methods code c ezaeg1a packaging type pressed carrier taping 2 mm pitch, 15,000 pcs. x ezaeg2a pressed carrier taping 2 mm pitch, 10,000 pcs. v ezaeg3a punched carrier taping 4 mm pitch, 5,000 pcs. design speci?cation code a design speci?cation rated voltage 30 v special feature code a special feature standard peak voltage code 50 peak voltage 500 v a b t w l protective coating alumina substrate gap electrode electrode (between) esd absorbent material electrode (outer) esd suppressor type: ezaeg ezaeg1a, 2a, 3a features esd protection of high-speed data lines low capacitance 0.04 pf : 0603(0201) size 0.05 pf : 1005(0402) size 0.10 pf : 1608(0603) size good esd suppression characteristics good esd withstanding rohs compliant explanation of part numbers dimensions in mm (not to scale) construction recommended applications high-speed data lines (hdmi, serial ata, usb, ieee1394, display port) antenna circuitry and rf modules (cellular phones) circuit confi guration type (inch size) dimensions (mm) mass (weight) [g/1000 pcs.] lwa b t ezaeg1a (0 201) 0.60 0.03 0.30 0.03 0.15 0.10 0.15 0.10 0.23 0.03 0.12 ezaeg2a (0 402) 1.00 0.10 0.50 0.05 0.20 0.10 0.25 0.10 0.38 0.05 0.6 ezaeg3a (0 603) 1.60 0.15 0.80 0.15 0.30 0.20 0.30 0.20 0.50 0.10 2.2 nov. 2012 01 5 6
design and speci cations are each subject to change without notice. ask factory for the current technical speci cations before purchase and/or use. should a safety concern arise regarding this product, please be sure to contact us immediately. esd suppressor -30 -25 -20 -15 -10 -5 0 5 1 10 100 1000 10000 frequency(mhz) attenuation (db) -50 0 50 100 150 200 250 300 350 400 -20 0 20 40 60 80 100 120 140 160 180 200 times (nsecs) volts (v) hdmi controller ) % . * 3 y 5 y antenna ga/as-sw or asm c a b esd suppressor type (inch size) dimensions (mm) abc ez aeg1a (0201) 0.3 to 0.4 0.8 to 0.9 0.25 to 0.35 ez aeg2a (0402) 0.5 to 0.6 1.4 to 1.6 0.4 to 0.6 ez aeg3a (0603) 0.7 to 0.9 2.0 to 2.2 0.8 to 1.0 (1) capacitance = the capacitance value shall be measured under the conditions specifi ed below. frequency : 1 mhz10 %, voltage : 1 vrms0.2 vrms, temperature : 25 c2 c (2) peak voltage = the peak voltage value shall be measured under the following conditions. esd test conditions : iec61000-4-2, 8 kv contact discharge (3) clamping voltage = the clamping voltage value shall be measured at 30 ns after initiation of pulse and measured under the c onditions specifi ed below. esd test conditions : iec61000-4-2, 8 kv contact discharge ratings frequency characteristics esd suppression voltage waveform typical circuits requiring protection hdmi circuit antenna circuit type ( inch size) capacitance (1) peak voltage (2) clamping voltage (3) rated voltage category temperature range ezaeg1a (0201) 0.04 +0.04 pf 500 v max. (350 v typ.) 100 v max. 30 v max C55 to +125 c ezaeg2a (0402) 0.05 +0.05 pf ezaeg3a (0603) 0.10 +0.10 pf C0.04 C0.03 C0.08 recommended land pattern design for esd suppressor is shown below. recommended land pattern packaging methods, soldering conditions and safety precautions please see data files nov. 2012 01 5 7
|